卷簾門其實用起來還是挺方便的，我相信不少人長期都會使用到卷簾門的。然而卷簾門稍微出一些故障就會影響到使用效果，所以我們非常有必要了解一些關于濟南卷簾門維修方法，以于在出現故障的時候可以找到有效辦法解決。

The roller shutter is actually very convenient to use. I believe many people will use it for a long time. However, a slight failure of the rolling shutter door will affect the use effect, so it is very necessary for us to know some maintenance methods of the rolling shutter door in Jinan, so that we can find effective solutions when the failure occurs.

卷簾門常見問題

FAQ of rolling shutter door

要說卷簾門常見問題的話，主要分為三個大點。

The common problems of rolling shutter doors can be divided into three major points.

塌腰，于塌腰的問題是普通卷簾門也是電動卷簾門容易出現的一個問題，出現的主要原因是因為廠家在對卷簾門進行組裝的是時候把本應為1.2毫米厚的鋼襯改成低于1.2毫米厚的，甚有些組裝廠根本就不放鋼襯，這樣經過一段時間后，就會發生塌腰。

Waist collapse. As for the problem of waist collapse, the common roller shutter door is also a common problem of electric roller shutter door. The main reason is that the manufacturer changed the steel lining that should be 1.2 mm thick to less than 1.2 mm thick when assembling the roller shutter door, and even some assembly plants did not put the steel lining at all. After a period of time, the waist collapse will occur.

密封不嚴，這個問題就出現在五金配件種，有些組裝電動卷簾門維修廠家采用低質偽劣的五金配件和膠條，以次充好，牟取暴利;或是安裝玻璃時不上玻璃墊塊，時間一長就會出現封閉不嚴甚掉扇現象。

The sealing is not tight, and this problem occurs in the hardware accessories. Some manufacturers that assemble electric roller shutter doors use low-quality and fake hardware accessories and rubber strips to make huge profits; Or if the glass cushion block is not installed when installing the glass, the sealing will not be tight or even the fan will fall off over a long period of time.

開裂，開裂的原因就是在組裝的過程中用盡過大，焊接溫度比較低的話也是容易導致焊腳開裂的。

The reason for cracking is that the exhaust is too large during the assembly process. If the welding temperature is relatively low, it is also easy to cause weld leg cracking.

卷簾門維修方法

Maintenance method of rolling shutter door

出現了問題那么我們就要找到解決問題的辦法，在出現問題之后我們要做到一看、二聽、三觸摸。

If there is a problem, we must find a way to solve it. After the problem occurs, we must look, listen and touch.

看主要是指元器件在電路板上的損傷。如組件故障，頭發黃，固定針松動，接觸，設備連接錯誤等。有經驗的維修人員會根據用戶提供的相關信息和故障現象，正確地觀察問題，迅速找到故障。

It mainly refers to the damage of components on the circuit board. Such as component failure, yellow hair, loose fixing pin, contact, wrong connection of equipment, etc. Experienced maintenance personnel will correctly observe the problem and quickly find the fault according to the relevant information and fault phenomenon provided by the user.

二聽就是卷簾門控制系統大多采用電磁繼電器作為控制器，繼電器觸點開關會產生明顯的“滴答”聲。作為無聲，在確定繼電器驅動電機無故障，可以確定繼電器壞。

Second, the roller shutter control system mostly uses electromagnetic relay as the controller, and the relay contact switch will produce an obvious "tick" sound. As silent, it can be determined that the relay is broken after confirming that the relay drive motor has no fault.

三觸摸就是經常接觸通電后的某些元素等集成器件穩定性建CC，變壓器，驅動二極管，感覺溫度是否正確，如快速加熱，溫度高，無短路故障電路可以識別壞設備。

Three-touch refers to the constant contact with some elements and other integrated devices after power-on to establish the stability of CC, transformer, drive diode, and feel whether the temperature is correct. For example, fast heating, high temperature, and no short-circuit fault circuit can identify bad equipment.

卷簾門維修之前以上就是檢查的基本，找到了事出的源頭那我們就可以很好的解決了。卷簾門在實際維修工作中，有時與配件，找出故障元件不更新，所以經常需要有處理突發事件的能力。更多相關事項就來我們網站http://www.emamhasanmojtaba.com進行咨詢！

The above is the basic inspection before the maintenance of the rolling shutter door. If we find the source of the problem, we can solve it very well. In the actual maintenance work, the roller shutter door sometimes works with the accessories to find out that the faulty components are not updated, so it often needs to have the ability to deal with emergencies. Come to our website for more relevant matters http://www.emamhasanmojtaba.com Consult!